Main Conclusion
This article covers four key practical topics: tightening‑torque application choices, washer functions, preload principles & nut‑factor calculation, plus threaded‑sleeve (helical‑coil insert) selection. Fastener joint reliability depends not only on parts quality but also on correct tightening practice, preload control, and thread‑repair solutions. Flange‑type fasteners can replace ordinary washers; tailless helical‑coil inserts are better suited for automated mass assembly.
| Section | Main Technical Points |
|---|---|
| 1. Bolt‑nut tightening: torque on bolt‑head or nut | No universal rule. Apply torque according to fit type, bearing‑surface size, material friction and bolt length. ‑Interference‑fit hole: torque the nut. ‑Different bearing areas: apply torque on the smaller‑surface side. ‑Dissimilar materials: torque on lower‑friction side. ‑Long bolts: torque nut to prevent bolt torsional winding. Mismatched torque‑application side will trigger insufficient pre‑load or over‑tightening failure. |
| 2. Purpose of washers | ① Disperse compressive stress to protect soft base‑material surfaces; prevent pull‑through failure. ② Compensate uneven mating surfaces for smooth assembly. ③ Special lock‑washers deliver anti‑loosening function. Limitation: rotating washers alter torque‑preload relation. Flange fasteners gradually replace washers, removing rotational interference. |
| 3. Preload working principle | Bolt behaves like a stretched spring: bolt tension generates joint clamping force. Formula T = KFD (Torque = nut‑factor × preload × bolt nominal diameter). ‑Nut‑factor K is affected by friction, material, surface finish and lubrication, leading to preload scatter. ‑Angle‑after‑torque method can stabilise preload but creates slight plastic deformation; such bolts are not suitable for reuse. |
| 4. Threaded‑sleeves (helical‑coil inserts) | Solve insufficient shear‑strength or damaged tapped‑holes for cast / forged components. ‑Tailed coil‑sleeve: high contact pressure, improves thread service‑life; requires post‑installation tail‑cutting, poor for automation. ‑Tailless helical‑coil sleeve: no tail‑cutting, bidirectional installation, no metal debris, fits blind holes and high‑volume automated production. |
Fasteners, commonly known as standard parts in the market, are mechanical components used to securely join two or more elements either mechanically or through adhesion. This article introduces some common issues related to fasteners for your reference.
I. How to Tighten Bolts and Nuts
Threaded connections using bolts and nuts are among the most common applications of fasteners. To ensure connection strength, self-locking nuts are typically used, or additional mechanical locking methods are applied to prevent loosening. Installing threaded fasteners is relatively simple—only sufficient torque is required to achieve the desired clamping force at the joint. However, many people remain uncertain about whether torque should be applied to the nut or the bolt head.
① Should torque be applied to the bolt head or the nut during tightening?
② Does applying torque to the bolt head yield the same result as applying it to the nut?

There is no definitive answer. In certain situations, it is perfectly acceptable to tighten the bolt head while securing the nut in place. However, in other applications, tightening only one component may be the only feasible option, depending on specific conditions such as stud welding (e.g., stud bolts or stud nuts), product design, materials, and installation requirements.
In some cases, you can apply torque to either the bolt head or the nut and still maintain a secure connection. However, under the following conditions, torque should generally be applied to only one part:
1. Interference Fit: When installing into an interference-fit hole, torque should be applied to the nut.
2. Different Shapes or Diameters: If the bolt head and nut differ in shape (e.g., hex head bolt with square nut) or diameter, it’s best to apply torque on the side with the smaller bearing surface. For example, if the bolt head is smaller than the nut, torque should be applied to the bolt head. A simple rule: apply force where it’s smaller, and let the larger end bear the load.
3. Different Materials: When clamping together two different materials, it’s preferable to apply clamping force on the material with the lower coefficient of friction—that is, apply torque on the side likely to generate less friction.
4. Long Bolts: Applying torque to the head of a long bolt increases the risk of torsional winding. Therefore, applying torque to the nut helps avoid this issue. Consider a case where the nut has a flange but the bolt head does not—the friction radius on the nut side is larger than that on the bolt head side. In such cases, if the tightening torque is determined based on nut tightening, applying the same torque to the bolt head could lead to overloading. Typically, nearly half of the applied torque is used to overcome friction beneath the clamping surfaces; thus, a smaller friction radius means more torque transfers into the thread interface, potentially causing over-tightening. Conversely, if the torque is calculated based on tightening the bolt head, applying it to the nut—where the friction radius is larger—will result in insufficient preload being delivered to the threads, increasing the risk of loosening.
II. Why Use Washers?
Washers are very common standard components frequently seen in threaded fastening operations involving bolts and nuts. In fact, washers are almost always used in conjunction with bolts or screws.

Why use washers?
① When the base material is soft, driving a bolt or screw into it may damage the surface of the parent material. Using a washer spreads the compressive force over a larger area, thereby protecting the surface from damage.
② If the base material is very soft and damage has already occurred around the hole where the fastener is installed, pull-through failure may occur during tightening. This happens because, in most cases, the force applied during tightening is sufficient to pull the fastener through the parent material. The presence of a washer helps generate a more evenly distributed pressure.
③ When the surface of the parent material into which bolts or screws are being driven is not smooth or flat, the head of the fastener may easily become stuck. Using a washer ensures that the bolt or screw can slide smoothly on the surface, making installation easier.
④ Some washers feature special structural designs that prevent nuts from loosening. These are commonly known as lock washers and come in various forms such as split-type, star-shaped, and wavy types. Such lock washers must be used in conjunction with nuts.
It is evident that, apart from specially designed lock washers, most washers primarily serve to distribute the load beneath the bolt head and nut face. In other words, for connection structures, washers mainly function to spread out the load. The primary reason threaded fasteners loosen after installation is usually due to lateral loads, which cause joint slip. Therefore, we always emphasize the importance of preload—sufficient preloading effectively prevents relative sliding at the joint interface, thereby avoiding loosening. However, effectively controlling preload during fastener installation remains a critical challenge. Even if thread specifications and installation tools remain unchanged, different operators may still result in insufficient preload.
Moreover, it’s important to note that when using washers, they are not fixed in place but can rotate along the axis of the threaded fastener. This rotation inevitably affects torque input and consequently influences preload. In recent years, flange-type fasteners have been increasingly used because flanges also offer effective load distribution and eliminate the aforementioned rotational issue. As a result, flange fasteners are gradually replacing washers in many applications.
III. The Role of Preload
When selecting bolt-nut connections, you apply torque via a torque tool or manual wrench to achieve clamping. This torque ultimately converts into the required preload at the joint. A certain level of preload ensures the joint resists vibration-induced loosening and fatigue. In most applications, higher preload is generally better.
How can preload be described? When tightening a bolt or nut, tension develops between the bolt head and nut. This tension acts like stretching a spring—the spring always tries to return to its original state, and similarly, the stretched bolt attempts to return to its original length to relieve this tension. This creates compressive or clamping forces that pull the bolt head and nut toward each other, thus clamping the joint tightly together. However, during the assembly process involving bolts and nuts, several other factors influence the magnitude of preload, including friction—both between the threads and between the threaded components and the joined parts. For this reason, we often discuss the abstract concept of the “nut factor” to determine the relationship between applied torque and resulting preload.
The formula T = KFD applies here, where T is the measured torque, K is the nut factor, F is the tensile force, and D is the bolt diameter. When using this equation, if K, F, and D are known, their product gives the required torque needed to tighten the bolt, ensuring the threaded connection achieves appropriate preload.
Among these variables, the nut factor K is relatively complex—so much so that its variations can significantly affect the difficulty of tightening. Factors influencing K include friction, materials of the bolt, nut, and washer, surface treatments, lubrication methods, and thread pitch. Because this involves numerous variables, these factors change for each different application, and even for different tightening cycles within the same application. Therefore, accurately determining the nut factor becomes crucial—and indeed challenging—for establishing the correct installation torque.
Practical experience shows that any assumed K value is not 100% reliable for a specific fastening application, and actual conditions during installation may lead to variations in the resulting preload. Some installations require rotating the bolt by a certain angle after reaching the target torque; this method aims to achieve the yield stage shown on the curve—where slight plastic deformation occurs—ensuring a consistent preload. However, this approach also has drawbacks: the fastener itself undergoes minor axial plastic deformation, which may prevent achieving the required preload upon reuse.
IV. Applications of Threaded Sleeves
Threaded sleeves are widely used in structural assembly, particularly on forged, cast, and machined components. They offer an effective solution when threaded holes lack sufficient shear area or cannot accommodate self-locking devices. For large forgings or castings, directly tapping threads into the base material could compromise the entire component if the threads become damaged.

Helical coil sleeves represent the simplest type of sleeve product, made by rolling high-quality stainless steel wire into a spring-like thread form. Typically, the outer diameter of the sleeve is slightly larger than the threaded hole, so compression occurs during installation. This serves two purposes: first, it maximizes contact area between the sleeve and the hole; second, the outward tension created by compression generates frictional force that locks the sleeve permanently in place.
Beyond mechanical strength, these products offer many advantages: thread life increases significantly even after repeated installation and removal. The sleeve’s hardness and smooth surface finish eliminate wear caused by thread friction. During installation, helical coil sleeves are secured without riveting or insertion locking, thus introducing no internal stresses into the base material. Helical coil sleeves can be mounted on plastic strips and wound onto spools, enabling much higher installation efficiency when using pneumatic tools. A drawback, however, is the need for tail-cutting after installation—the “tail” on the sleeve merely serves as a guide during installation and adds no structural benefit. Removing it requires specialized tools, which can reduce assembly efficiency.
Therefore, tailless helical coil sleeves have gained widespread use. These retain all the benefits of their tailed counterparts but eliminate the need for post-installation tail cutting. Their guiding function is achieved through grooves cut into the spiral wire. Compared to traditional tailed sleeves requiring tail-cutting, tailless versions offer the following advantages:
① Eliminates the tail-cutting process, making them ideal for high-volume automated installation;
② Features a bidirectional groove design, eliminating the need to check insertion direction before each installation;
③ No tail-cutting means no risk of generating debris during installation;
④ No need to purchase tail-cutting tools.
In blind-hole applications, traditional tailed sleeves often require extra space beneath the hole to complete the final tail-cutting operation, while ensuring the process does not damage the base material. With tailless sleeves, this additional space requirement is greatly reduced.
V. Conclusion
Through the above introduction, we have learned whether torque should be applied to the bolt head or the nut during tightening and the corresponding situations, the function of washers and the development of flange fasteners, how to ensure the required preload for installation, as well as the functions and advantages and disadvantages of thread inserts.
If you are looking for quality fasteners, please visit us here https://hktl-fastener.com/